source: soft/giet_vm/giet_drivers/sdc_driver.h @ 487

Last change on this file since 487 was 437, checked in by alain, 10 years ago

Introducing dynamic allocation of peripheral channel(TTY, NIC, TIM, CMA)
Removint the ICU driver : ICU component not supported anymore.
Removing the FBF driver.

File size: 5.8 KB
Line 
1///////////////////////////////////////////////////////////////////////////////////
2// File     : sdc_driver.h
3// Date     : 31/08/2012
4// Author   : cesar fuguet
5// Copyright (c) UPMC-LIP6
6///////////////////////////////////////////////////////////////////////////////////
7
8#ifndef _GIET_SDC_DRIVER_H_
9#define _GIET_SDC_DRIVER_H_
10
11#include <ioc_driver.h>
12#include <spi_driver.h>
13#include <mapping_info.h>
14
15///////////////////////////////////////////////////////////////////////////////
16// SD card structure definition
17///////////////////////////////////////////////////////////////////////////////
18struct sdcard_dev
19{ 
20    // SPI controller pointer
21    struct spi_dev * spi;
22
23    // block length of the SDCARD
24    unsigned int block_length;
25
26    // access pointer representing the offset in bytes used to read or write in
27    // the SDCARD. This driver is for cards SDSD, therefore this offset must be
28    // multiple of the block length
29    unsigned int access_pointer;
30
31    // slave ID. This ID represents the number of the slave select signal used
32    // in the hardware platform (SPI channel)
33    int slave_id;
34
35    // is the card high capacity ?
36    int sdhc;
37};
38
39///////////////////////////////////////////////////////////////////////////////
40// This function initializes the SPI controller and call sdc_open to
41// initialize  the SD card
42// - channel: channel to initialize (only channel 0 supported)
43// Returns 0 if success, other value if failure
44///////////////////////////////////////////////////////////////////////////////
45unsigned int _sdc_init();
46
47///////////////////////////////////////////////////////////////////////////////
48// Transfer data from the block device to a memory buffer.
49// - mode     : BOOT / KERNEL / USER
50// - lba      : first block index on the block device
51// - buffer   : base address of the memory buffer (must be word aligned)
52// - count    : number of blocks to be transfered.
53// Returns 0 if success, > 0 if error.
54///////////////////////////////////////////////////////////////////////////////
55unsigned int _sdc_read( unsigned int mode,
56                        unsigned int lba,
57                        paddr_t      buffer,
58                        unsigned int count);
59
60
61///////////////////////////////////////////////////////////////////////////////
62// Transfer data from memory buffer to SD card device.
63// - mode     : BOOT / KERNEL / USER
64// - lba      : destination first block index on the SD card
65// - buffer   : base address of the memory buffer (must be word aligned)
66// - count    : number of blocks to be transfered.
67// Returns 0 if success, > 0 if error.
68// WARNING: The _sdc_write() is not implemented yet.
69///////////////////////////////////////////////////////////////////////////////
70unsigned int _sdc_write( unsigned int mode,
71                         unsigned int lba,
72                         paddr_t      buffer,
73                         unsigned int count);
74
75///////////////////////////////////////////////////////////////////////////////
76// This function should not be called for the SDC card.
77///////////////////////////////////////////////////////////////////////////////
78unsigned int _sdc_get_status();
79
80///////////////////////////////////////////////////////////////////////////////
81// Returns the block size in bytes of the SD card.
82///////////////////////////////////////////////////////////////////////////////
83unsigned int _sdc_get_block_size();
84
85
86///////////////////////////////////////////////////////////////////////////////
87// SD card constants
88///////////////////////////////////////////////////////////////////////////////
89
90// Number of retries after an unacknowledge command
91#define SDCARD_COMMAND_TIMEOUT  100
92
93// This command is a simple SD commmand
94#define SDCARD_CMD              0
95
96// This is an application specific command
97#define SDCARD_ACMD             1
98
99// The transmition is done in the negative edge of the clock
100#define SDCARD_TX_NEGEDGE       0
101
102// The transmition is done in the positive edge of the clock
103#define SDCARD_TX_POSEDGE       1
104
105// The reception is done in the negative edge of the clock
106#define SDCARD_RX_NEGEDGE       0
107
108// The reception is done in the positive edge of the clock
109#define SDCARD_RX_POSEDGE       1
110
111///////////////////////////////////////////////////////////////////////////////
112// SD card macros
113///////////////////////////////////////////////////////////////////////////////
114
115///////////////////////////////////////////////////////////////////////////////
116//   SDCARD_CHECK_R1_VALID()
117// This macro checks if the SD card response is valid
118// - x: SD card response
119// Returns 1 if valid and 0 otherwise
120///////////////////////////////////////////////////////////////////////////////
121#define SDCARD_CHECK_R1_VALID(x)    (~x & SDCARD_R1_RSP_VALID) ? 1 : 0
122
123///////////////////////////////////////////////////////////////////////////////
124//   SDCARD_CHECK_R1_ERROR()
125// This macro checks if there is an error in SD card response
126// - x: SD card response
127// Returns 1 if error and 0 otherwise
128///////////////////////////////////////////////////////////////////////////////
129#define SDCARD_CHECK_R1_ERROR(x)    ( x & 0x7E)                ? 1 : 0
130
131// SD card response 1 (R1) format constants
132#define SDCARD_R1_IN_IDLE_STATE     ( 1 << 0 ) // R1 bit 0
133#define SDCARD_R1_ERASE_RESET       ( 1 << 1 ) // R1 bit 1
134#define SDCARD_R1_ILLEGAL_CMD       ( 1 << 2 ) // R1 bit 2
135#define SDCARD_R1_COM_CRC_ERR       ( 1 << 3 ) // R1 bit 3
136#define SDCARD_R1_ERASE_SEQ_ERR     ( 1 << 4 ) // R1 bit 4
137#define SDCARD_R1_ADDRESS_ERR       ( 1 << 5 ) // R1 bit 5
138#define SDCARD_R1_PARAMETER_ERR     ( 1 << 6 ) // R1 bit 6
139#define SDCARD_R1_RSP_VALID         ( 1 << 7 ) // R1 bit 7
140
141#endif
142
143// Local Variables:
144// tab-width: 4
145// c-basic-offset: 4
146// c-file-offsets:((innamespace . 0)(inline-open . 0))
147// indent-tabs-mode: nil
148// End:
149// vim: filetype=c:expandtab:shiftwidth=4:tabstop=4:softtabstop=4
Note: See TracBrowser for help on using the repository browser.