Context Navigation

reset.S @ 755

Last change on this file since 755 was 755, checked in by cfuguet, 10 years ago

tsar_boot: preloader stack

During preloader execution, only processor 0 initializes its stack.

The stack allocation for other processors must be done by the loaded Operating System during its boot loader execution.

The stack size for processor 0 is defined by the RESET_STACK_SIZE preprocessor constant in the defs.h file. For now it is 8 Kbytes and it can be changed if further modifications in the preloader need it.

File size: 7.4 KB

Line
1	/*
2	* \file : reset.S
3	* \date : 01/12/2012
4	* \author: Cesar FUGUET & Manuel BOUYER & Alain Greiner
5	*
6	* This is a generic reset code for a generic multi-clusters / multi-processors
7	* TSAR architecture (up to 256 clusters / up to 4 processors per cluster).
8	*
9	* There is one XICU, one TTY, one DMA, and one memory bank per cluster.
10	*
11	* This preloader uses a stack segment allocated in cluster 0 for processor 0.
12	* The stack allocation is not performed for other processors as they do not
13	* need it during the preloader execution. Therefore, this allocation should be
14	* done by the loaded Operating System.
15	*
16	* The replicated XICU is used to awake the sleeping processors:
17	* xicu_paddr_base = ICU_PADDR_BASE + (cluster_xy << 32)
18	*
19	* It is intended to be used with various operating systems or nano kernels,
20	* including NetBSD, Linux, ALMOS, and GIET_VM.
21	*
22	* - Each processor initializes its Status Register (SR) to disable interrupts.
23	* - Each processor initializes its Count Register.
24	* - Each processor initialises its private XICU WTI mask register.
25	* - Only processor 0 executes the reset_load_elf function to load into memory
26	* the system specific boot-loader stored on disk at BOOT_LOADER_LBA
27	* - All other processors wait in a low power consumption mode that the
28	* processor 0 wakes them using an IPI (Inter Processor Interruption)
29	*/
30
31	#include <defs.h>
32	#include <mips32_registers.h>
33
34	/* These define should be consistent with values defined in map.xml file */
35
36	.section .reset,"ax",@progbits
37
38	.extern dtb_addr
39	.extern reset_putc
40	.extern reset_getc
41	.extern reset_ioc_read
42	.extern reset_elf_loader
43	.extern memcpy
44	.extern reset_puts
45	.extern reset_putx
46	.extern reset_putd
47	.extern reset_ioc_init
48	.extern versionstr
49
50	.globl reset /* Makes reset an external symbol */
51	.ent reset
52
53	.align 2
54	.set noreorder
55
56	reset:
57	b _reset /* 0xbfc0000 */
58	nop /* 0xbfc0004 */
59
60	/* Addresses of the functions provided by this reset code */
61
62	preloader_vector:
63	.word RESET_VERSION /* 0xbfc0008 */
64	.word dtb_addr /* 0xbfc000c */
65	.word reset_putc /* 0xbfc0010 */
66	.word reset_getc /* 0xbfc0014 */
67	.word reset_ioc_read /* 0xbfc0018 */
68	.word reset_elf_loader /* 0xbfc001C */
69	.word memcpy /* 0xbfc0020 */
70	.word reset_puts /* 0xbfc0024 */
71	.word reset_putx /* 0xbfc0028 */
72	.word reset_putd /* 0xbfc002C */
73
74	_reset:
75
76	/* All processors Disable interruptions, keep STATUSbev enabled */
77
78	li k0, (1 << 22)
79	mtc0 k0, CP0_STATUS
80
81	/* All processors compute pid, lpid, cluster_xy */
82
83	mfc0 k0, CP0_EBASE
84	andi t0, k0, 0x3FF /* t0 <= pid (at most 1024 procs) */
85
86	move t3, t0
87
88	la k0, NB_PROCS /* k0 <= # of processors per cluster */
89	divu t3, k0
90	mfhi t1 /* t1 <= lpid = pid % NB_PROCS */
91	mflo t2 /* t2 <= cluster_xy = pid / NB_PROCS */
92
93	/* All processors initialise the count register in CP0 */
94
95	mtc0 zero, CP0_COUNT
96
97	/*
98	* All processors enable the WTI for XICU
99	* Each processor may have IRQ_PER_PROC irq outputs from the XICU
100	* In each cluster, the XICU base address depends on the cluster_xy
101	*/
102
103	la t3, ICU_PADDR_BASE /* t3 <= ICU base address */
104	move t4, t1 /* t4 <= local_id */
105	li t5, IRQ_PER_PROC /* t5 <= IRQ_PER_PROC */
106	multu t4, t5
107	mflo t6 /* t6 <= IRQ_PER_PROC * local_id */
108	sll t4, t6, 2 /* t4 <= OUT_INDEX = t6 * 4 */
109
110	li t5, (0xC << 7) /* t5 <= FUNC = XICU_MSK_WTI */
111	or t4, t4, t5 /* t4 <= FUNC \| INDEX \| 00 */
112	or t5, t3, t4 /* t5 <= &XICU[MSK_WTI][OUT_INDEX] */
113
114	/* All processors set WTI mask using the physical address extension */
115
116	li t4, 1
117	sllv t4, t4, t1 /* Set XICU[MSK_WTI][INDEX][local_id] */
118
119	mtc2 t2, CP2_PADDR_EXT /* set PADDR extension */
120	sw t4, 0(t5) /* XICU[MSK_WTI][INDEX] <= t4 */
121	mtc2 zero, CP2_PADDR_EXT /* reset PADDR extension */
122
123	/*
124	* Only processor 0 in cluster 0 loads and executes the boot-loader
125	* We have:
126	* t0: global pid
127	* t1: local pid
128	* t2: cluster_xy
129	* t3: xicu physical base address in cluster 0
130	*/
131
132	bne zero, t0, _reset_wait
133	nop
134
135	/* Processor 0 initializes stack pointer */
136
137	la k0, _stack
138	li k1, RESET_STACK_SIZE /* k1 <= P0 stack size */
139	addu sp, k0, k1 /* P0 stack from base to (base + size) */
140
141	/* Processor 0 displays version for this reset code */
142
143	la a0, versionstr
144	la k0, reset_puts
145	jalr k0
146	nop
147
148
149	#if USE_SPI
150
151	/* Processor 0 Initialize the SPI controller */
152
153	la k0, reset_ioc_init
154	jalr k0
155	nop
156
157	#endif
158
159	/*
160	* Processor 0 jumps to the reset_elf_loader routine passing as argument
161	* the block number in which is loaded the .elf file
162	*/
163
164	la k0, reset_elf_loader
165	li a0, BOOT_LOADER_LBA
166	jalr k0
167	nop
168
169	/*
170	* Processor O jumps to the entry address defined in the .elf file, and
171	* returned by reset_elf_loader function.
172	* First argument is pointer to the preloader function vectors other
173	* function arguments are 0
174	*/
175
176	la a0, preloader_vector
177	move a1, zero
178	move a2, zero
179	move a3, zero
180	jr v0
181	nop
182
183	/*
184	* All processor (but processor 0) wait in low power mode until processor 0
185	* wakes them using an IPI.
186	* We have:
187	* t0: global id
188	* t1: local id
189	* t2: cluster id
190	* t3: xicu physical base address in cluster 0
191	*/
192
193	_reset_wait:
194
195	sll t4, t1, 2 /* t4 <= local_id * 4 */
196	addu t5, t4, t3 /* t5 <= &XICU[WTI_REG][local_id] */
197
198	wait
199
200	/*
201	* All other processors, when exiting wait mode, read from XICU the address
202	* to jump.
203	* This address is the boot-loader entry address that has been written in
204	* the mailbox by the IPI sent by processor 0
205	*/
206
207	mtc2 t2, CP2_PADDR_EXT /* set PADDR extension */
208	lw k0, 0(t5) /* k0 <= XICU[WTI_REG][local_id] */
209	mtc2 zero, CP2_PADDR_EXT /* reset PADDR extension */
210
211	jr k0
212	nop
213
214	/* Exception entry point */
215
216	.org 0x0380
217	_excep:
218	mfc0 a0, CP0_STATUS /* first arg is status */
219	mfc0 a1, CP0_CAUSE /* second arg is cause */
220	mfc0 a2, CP0_EPC /* third argc is epc */
221	mfc2 a3, CP2_DBVAR /* fourth argc is dbvar */
222	nop
223	j handle_except
224	nop
225
226	.end reset
227
228	.set reorder
229
230	.section .data
231
232	_stack:
233
234	.space RESET_STACK_SIZE
235
236	/*
237	* vim: tabstop=4 : shiftwidth=4 : expandtab
238	*/

Note: See TracBrowser for help on using the repository browser.

Download in other formats:

Original Format