source: anr/task-4.tex @ 283

Last change on this file since 283 was 278, checked in by coach, 14 years ago

Reduced the task number. Suppressed xilinx, navtel and flexra. Added mds.

File size: 3.4 KB
Line 
1\begin{taskinfo}
2\let\UBS\leader
3\let\UPMC\enable
4\let\TIMA\enable
5\let\XILINX\enable
6\end{taskinfo}
7%
8\begin{objectif}
9The objectives of this task are to provide the two HAS back-ends of the COACH project and
10a tool that adapt the coprocessor frequency to the FPGA-SoC frequency as required
11by the processors and the system bus.
12\\
13The HAS back-ends as shown in figure~\ref{archi-hls} reads an \xcoach description and provides an
14\xcoachplus description, i.e. an \xcoach description  annotated with hardware information such as
15variables binding to registers, operations bindings to cells/fonctional units, operation scheduling...
16The \xcoach format being generated by the \novers{\specXcoachToCA} deliverable and the \xcoachplus being treated by
17the \novers{\specXcoachToSystemC} and the \novers{\specXcoachToVhdl} deliverables,
18this task strongly depends on task~1.
19\par
20For the two HAS front-end, this task is based on the already existing HLS tools GAUT and
21UGH. These tools are complementary and not in competition because they cover respectively
22data and control dominated designs.
23\end{objectif}
24
25\begin{workpackage}
26\subtask{Making HAS back-end to read \xcoach format}
27    The goal of this \ST is to integrate the UGH and GAUT HLS tool to the COACH framework.
28    by implementing the mechanism to read \xcoach format.
29    \begin{livrable}
30    \itemL{6}{12}{x}{\Stima}{UGH integration}{12:0:0}
31        Release of the UGH software that reads \xcoach format.
32    \itemL{6}{12}{x}{\Subs}{GAUT release reading \xcoach}{6:0:0}
33        Release of the GAUT software that is able to read \xcoach format.
34    \end{livrable}
35%
36\subtask{Making HAS back-end to write \xcoachplus format}
37    The goal of this \ST is to integrate the UGH and GAUT HLS tool to the COACH framework.
38    by implementing the mechanism to write \xcoachplus format.
39    \begin{livrable}
40    \itemL{12}{18}{x}{\Supmc}{UGH integration}{0:2:4.0}
41        Release of the UGH software that writes \xcoachplus format.
42    \itemL{12}{18}{x}{\Subs}{GAUT release writing \xcoachplus}{0:6:0}
43        Release of the GAUT software that is able to read \xcoach format and to write \xcoachplus format.
44    \end{livrable}
45
46\subtask{Coprocessor frequency adaptation}
47    In FPGA-SoC, the frequency is given by the processor(s) and the system BUS. The coprocessors
48    generated by HLS synthesis must respect this frequency. However, the HLS tools can not
49    guarantee that the micro-architectures they generate accurately respect this
50    frequency. This is especially the case when the target is a FPGA device, because the
51    delays are really known only after the RTL synthesis and that estimated delays used
52    by the HLS are very inaccurate. The goal of this \ST is to provide a tool that adapts
53    the coprocessors frequency to the FPGA-SoC frequency after the coprocessor RTL
54    synthesis.
55    \begin{livrable}
56    \itemV{0}{12}{d}{\Supmc}{Frequency calibration}
57        A document describing the set up of the coprocessor frequency calibration.
58    \itemV{12}{24}{x}{\Supmc}{Frequency calibration}
59        \setMacroInAuxFile{freqCalibrationVhdl}
60        A VHDL description of hardware added to the coprocessor to enable the calibration.
61    \itemL{24}{33}{x}{\Supmc}{Frequency calibration}{2:.5:3.5}
62        The frequency calibration software consists of a driver in the FPGA-SoC operating
63        system and of a control software.
64    \end{livrable}
65\end{workpackage}
Note: See TracBrowser for help on using the repository browser.